Component Checklist
Roll / Shift Adjustment
Component Checklist
A
Check you have received all parts against the Component Checklist above.
Bits Bag
WARNING
WARNING: This bracket supports up to 15kg (33lbs).
It is dangerous to overload this bracket.
Ensure the Ceiling can support the total weight of the Projector and the Universal Ceiling Mount.
All bolts and screws must be used at the designated points as per installation instructions to prevent damage
to the projector unit, or injury.
DO NOT install near an air conditioner or where there is excessive dust and smoke.
Ensure the projector is mounted so that it is not possible for undue load to be placed on the bracket.
Extension Brackets
150mm (x2)
Extension Brackets
75mm (x2)
Cross Recessed Screws
M2.5x15 (x4)
M3x15 / M3x20 (x4 each)
M4x15 / M4x20 / M4x25 (x4 each)
M5x15 / M5x20 / M5x25 (x4 each)
M6x15 / M6x20 / M6x25 (x4 each)
M5x10mm
Socket Button
Cap Screw (x4)
Spacer
Large (x4)
Medium (x4)
Small (x4)
6mm Allen
Key (x1)
Bottom
Spacer (x4)
Ceiling Mount
Assembly (x1)
Nylon Anchor
Plug (x4)
14 Gauge Coach Screw (x4)
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 08.02.13©
G.1.
Connect the Shaft to the Bottom Ceiling Hanger as
shown below.
Installation Instructions
Please read these
instructions before
commencing installation
as faulty installation could
result in injur y . Atdec
assumes no responsibility
for faulty installations.
IMPORTANT
Assembling the Mounting Plate and the Fixing Coupler
B
G
Adjust i n g t h e Projec t or
H
G.2.
Insert the Locking
Hook into the slot in
the Bottom Ceiling
Hanger to lock
the Ceiling Mount
Assembly.
Bottom
Ceiling
Hanger
Locking
Hook
M8 Nyloc Nut
M8x50mm
Socket Cap
Screw
Locking
Hook
6mm
Allen Key
Ceiling Mount
and Pro j ec tor
M8x15mm
Screw
6mm
Allen Key
6mm
Allen Key
6mm
Allen Key
Assemble the Mounting
Plate and the Fixing
Coupler as shown, then
move onto the next step to
attach it to the ceiling.
Pitch Adjustment
3mm Allen
Key (x1)
To make Roll/Shift adjustments, first ensure the
weight of the projector is supported. Then loosen
the M8x65mm Screw with the supplied 6mm
Allen Key, and adjust to your desired position.
Re-tighten the screw firmly.
To make Pitch adjustment, first ensure the weight
of the projector is supported. Then loosen both
M8x15mm Screws with the supplied 6mm Allen
Key, and adjust to your desired position.
Re-tighten both screws firmly.
Shift
Washer
20mm (x4)
10mm (x4)
8mm (x4)
Square
Nut (x8)
Shaft
M8x50mm Socket
Head Cap Screw (x8)
M8 Nyloc
Nut (x8)
Mounting
Plate (x1)
Fixing Coupler
(x1)
Top Ceiling
Hanger (x1)
Bottom Ceiling
Hanger (x1)
Mid Ceiling
Hanger (x1)
Mounting Plate
Fixing Coupler
NOTE
If mounting
onto an angled
ceiling, ensure
the Fixing
Coupler is in
the correct
orientation.
angled
ceiling
Fixing
Coupler
Pitch Pitch
Tip: When the projector requires servicing, remove
the projector via this easy disconnection point to
save time.
Extension Brackets
100mm (x2)
Extension Brackets
50mm (x2)
G.3.
Tighten the Locking Hook with the supplied
M8x50mm Socket Cap Screw and the M8 Nyloc
Nut.
Projector Ceiling Mount |Pole
TM
Tighten
Loosen
Loosen
Roll
Roll
M8x65mm
Screw
Attaching the Ceiling Mount Assembly to the Ceiling Hanger
Installation Complete
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals