Atdec TH-1030-VFM Specifications download pdf

Step 7. Final Adjustment

Installation Complete

Your Telehook Wall Mount Swing Arm is complete and ready to use.

Position and angle your Display as desired, ensuring the Swing Arm moves freely.

Adjust the tension of the joints to suit, using the Allen Keys supplied.

4mm Allen Key

6mm Allen Key

As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.11.09 ©

LOOSEN

TIGHTEN

LOOSEN

TIGHTEN

Step 6. Cable Management

127( Leave enough

slack in the cables to

allow for full movement.

Connect cables

Cable Cover (x2)

Cable Clip

To utilise the Telehook Swing Arm cable

management system, use the Cable Covers

and Cable Clip as shown.

IMPORTANT INFORMATION

,03257$17,QVWDOO7HOHKRRN:DOO0RXQW6ZLQJ$UPDVSHUWKH,QVWDOODWLRQ,QVWUXFWLRQV

! Telehook Wall Mount Swing Arm supports displays weighing up to 20kg (44lbs), with VESA hole configurations:

75x75mm (3”x3”), 100x100mm (4”x4”), *200x100mm (8”x4”), and *200x200mm (8”x8”) (*using extension tabs supplied)

! The Manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Installing the Wall Bracket

Component Checklist

Stud

Masonry Wall

Nylon Anchor (x2)

Wall Mount

Screw (x2)

Wall Mount

Screw (x2)

Wall Material

Hardware

Flat Screen Wall Mount | Swing Arm

Installation Instructions

TOOLS REQUIRED:

Power Drill

4mm (

”) Drill Bit

11mm (

”) Masonry Drill Bit

Phillips Head Screwdriver

Spirit Level

Mounting to a 7LPEHU6WXG:DOO Mounting to a 0DVRQU\:DOO:

7+9)0

Swing Arm

Vesa Plate

- Position the Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (2

“) deep holes using an 11mm (

”)

masonry drill bit.

- Secure the Wall Bracket using the Wall Mount Screws and

Nylon Anchors supplied.

- Position Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (2

”) deep holes using a 4mm (

”) drill bit.

- Secure the Wall Bracket using the Wall Mount Screws supplied.

2.5mm Allen Key

4mm Allen Key

5mm Allen Key

6mm Allen Key

Washer (x4)

Nylon Anchor (x2)

Wall Mount Screw (x2)

Wall Bracket

Extension

Tabs (x4)

Extension Mounting Screws

M4x12mm/M4x16mm (x4 each)

M5x12mm/M5x16mm (x4 each)

M6x12mm/M6x16mm (x4 each)

Display Mounting Screws

M5x12mm (x4)

1 2

Installation Instructions 1

Summary of Contents

Page 1 - Installation Instructions

Step 7. Final AdjustmentInstallation CompleteYour Telehook Wall Mount Swing Arm is complete and ready to use.Position and angle your Display

Page 2

75 or 100mmVESATop ofDisplayStep 4. Attach the VESA plate to your DisplayFasten the VESA plate to your Display using the Display Mounting screws an

Comments to this Manuals

No comments

Atdec TH-1030-VFM Specifications

Browse online or download Specifications for Flat panel wall mounts Atdec TH-1030-VFM. Atdec TH-1030-VFM flat panel wall mount User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Flat panel wall mounts Atdec TH-1030-VFM